Long time ago before I attend my CCNA in Penang, I have no idea how those Network Administrator/IT Engineer configure Cisco router and switch. Just know they have good knowledge on the cisco coding.
While configure a cisco router, there are few kind of mode can be use:
- User Mode
- Priviledge Mode
- Config Mode
- Interface Mode
- line mode
Cisco Router Basic Configuration Need:
- Password + Secret
- Hostname
- Interface (IP and subnet mask, no shut, and clock rate)
- Line configuration
Below are some coding on Basic configuration for cisco router:
Enter Privilege Mode
Router > enable
Enter Configuration Mode
Router# configuration terminal
Password need when enter into Privilege Mode next time
Router(config)# enable password p@ssw0rd
Router(config)#enable secret s3cr3t
Configure Hostname / Router Name
Router(config)#hostname myrouter1
[Set the hostname to myrouter1]
Configure Ethernet Port Command
myrouter1(config)# inte f0/0
[Enter Ethernet Interface Mode ( f0/0 for interface1, f0/1 for interface 2)]
myrouter1(config-if)# ip add 192.168.0.1 255.255.255.0
[Set IP address and subnet mask]
myrouter1(config-if)#no shut
[Active the port]
Configure Serial Port Command
myrouter1(config-if)#inte s 0/0/0
[Enter Serial Interface Mode]
myrouter1(config-if)#ip add 192.168.20.1 255.255.255.0
[Set IP address and subnet mask]
myrouter1(config-if)#no shut
[Active the port]
Set the Router Bandwidth – Set the bandwidth to 1G, Clock Rate only apply at Master Router
myrouter1(config-if)#clock rate 1000000
[Set the bandwidth to 1Gig]
myrouter1(config-if)#exit
Secure Console
myrouter1(config)#line con 0
myrouter1(config-line)#password c0ns0l3
myrouter1(config-line)#login
myrouter1(config-line)#exit
Secure Aux line – Auxiliary Password, use to connect a modem to a router for remote console connection, Aux only available for old router, new router does not apply
myrouter1(config)#line aux0
myrouter1(config-line)#password auXo
myrouter1(config-line)#login
myrouter1(config-line)#exit
Secure VTY line – Virtual Terminal Password, Use to secure your login from telnet or ssh
myrouter1(config)#line vty 0 4
myrouter1(config-line)#password v1rtu@1
myrouter1(config-line)#login
myrouter1(config-line)#exit
myrouter1(config)#exit
Save setting
myrouter1#wr me
or
myrouter1#copy run start
The above code are just a very basic configuration for cisco router, there are more advance configuration need for routing purpose such as static routes, default routes and dynamic routes. Within dynamic routes, there are also RIP Routes (Routing Information Protocol), IGRP Routes (Interior Gateway Routing Protocol) OSPF Routes (Open Shortest Path First) and EIGRP Routes (Enhanced Interior Gateway Routing Protocol)
All this routing require different command for different protocol, I am still studying on all this cisco command, and soon, will post the easy explanation here when I have better understanding on cisco router routing configuration. To master the cisco router basic configuration, have to do more practice on Packet Tracer, Cisco Simulation Software. To learn how to use packet tracer , you also can visit the Packet Tracer Video Tutorial that I post quite some time ago, another Packet Tracer Video Tutorial Part 3 is coming up soon 🙂
hi there! hmmm..this info is mind-boggling,hehehe! My two bros-in-law are in to this stuff, they’re both ECEngineers but the “heck”!!! i really dont have the nerves to try their field,hehehehe! thanks for dropping a comment on my site buddy! wish u luck!!!!
sunny >
Thank for your visit, I hope one days i will pro like ur bros-in-law
Recently I can’t access to my router using the existing password for some reasons, I wonder it has been hacked or device malfunction.
ChampDog >
There are also some device password recovery step, I try to make a time, post it here 🙂
That will be great. I haven’t got a chance to fix it. The time I realized it, I need to travel to oversea already.
ChampDog,
i suggest u to enable the ssh access to ur router/modem.
it would be easier for u to manage ur router/modem remotely.
If u do not have a static IP, just register in dyndns.com and enable the ddns in your router/modem.
it is safe to enable this.
I am very very very much having a big big big trouble on this one. I passed CCNA 1 and am now into CCNA 2 but I still don’t understand these stuffs. I am so stupid. Thanks for this one. it’s a big help!
hi its to good and easy to learn but i want it continu
has been searching this for very long time already, do you have other configuration tutorial such as HP, and 3Com switch and router?
it is very pretty.
Hi,
Currently I’m working at TIME dotCom as a network engineer, do you now the current market price for a freelancer to charge a customer to provide services for configuring a Cisco 2811 router? Thanks
tae,, sarap mag routing,,,,
i want to become a cisco router configurator.
it was a very well compiled material…u have done a excellent job..thx 🙂
hhmmmm this is very easy tips plz keep this process continu
this is subperb my sweet bro .. today i first time open the packet tracer , and did not know what to do .. but when i see ur stuff it gave me quite good info ..best of luck .. waiting for next coming document
pota bogo… LITSE KA!!!!!!!!!!!
tq…. the configuration here make me understood to do my homework….
what is clock rate & why your are use 100000.
It’s a Nice configuration
Hi..thanks a lot
ooops! just got some satisfaction with your stuff…unlock more, would be very appreciative
Hey..in cisco, all you very need to know is Ip, even you are very good in commands but if you do not know how to figure out your Ip you can be in very big trouble.
You need to know 4 things in IP address: class, host, subnet and wildcard. and you must figure out this answer in under 1 minute..if you can get this things done in 1 minutes..you are good to go , command is very important too 🙂
Just and idea..before you move forward to further cisco,, please makesure IP address is first..and the 7 layer. 🙂
it works but i also need routing techniques and further steps
thanks
Thanx a lot it was so nyc.